Plans for transmitter tray
#1
Junior Member
Thread Starter
Join Date: May 2002
Location: Hanover Park,
IL
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Plans for transmitter tray
Looking for plans for a transmitter tray with metal straps that hook over the shoulders. I'm told the manufacturer has discontinued them, but that plans are available. Please let me know if you have them or know where to obtain them. Thanks.
#2
Senior Member
Join Date: Mar 2002
Location: New Mexico
Posts: 139
Likes: 0
Received 0 Likes
on
0 Posts
Plans for transmitter tray
I make them for my friends here locally. Look really nice. Cost is around $15 from a Home Depot or similar. Maybe i should draw up some plans.
Maybe the best thing to do is take pictures and explain it. Drawings can get a bit confusing. Give me a couple weeks
Email me and I'll try and get detailed
Maybe the best thing to do is take pictures and explain it. Drawings can get a bit confusing. Give me a couple weeks
Email me and I'll try and get detailed
#5
Senior Member
My Feedback: (19)
Join Date: Dec 2001
Location: Evansville, IN
Posts: 2,156
Likes: 0
Received 0 Likes
on
0 Posts
Plans for transmitter tray
It may not be what you want but I have one I built from howard sullivans plans and no longer use. I would sell it for 12 bucks shipped. It is wood base with alum arms about 14" long you then attach a camera strap to. You can see the plans on rc flight unlimited (howard's site) http://webpages.charter.net/rcfu/
#6
Junior Member
Thread Starter
Join Date: May 2002
Location: Hanover Park,
IL
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Transmitter tray
Thanks to 4*60 for the tip on the tray plans. The site does take a while to load, but once up it includes a great photo and excellent plans. Ther are other plans there as well. Thanks to Dick Layahe of Franklin County Aircraft Modelers for putting the plans together and posting them. These plans will save me a ton of time and avoid mistakes.
Been in this hobby a week and I'm already overwhelmed at how all you vets are willing to help us rookies.
Thanks again.
Been in this hobby a week and I'm already overwhelmed at how all you vets are willing to help us rookies.
Thanks again.
#7
Member
Join Date: Feb 2002
Location: SE Michigan
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Plans for transmitter tray
Amen to that!
I can't believe how great the vets are to us new guys. There is a lot of great hard won information flying around here (pun intended) that would take us many a hard landing to glean without.
When I first went to the flying field for my club, the guys on the flight line pulled me into the pits and gave me a quick shake down on what was going on.
Then proceeded to do some of the nicest maneuvers that I'd ever seen. The good PR had me signed up shortly thereafter, and I have had no second thoughts.
Thanks again guys. Keep the advice flowing.
Clear skies,
Auger
I can't believe how great the vets are to us new guys. There is a lot of great hard won information flying around here (pun intended) that would take us many a hard landing to glean without.
When I first went to the flying field for my club, the guys on the flight line pulled me into the pits and gave me a quick shake down on what was going on.
Then proceeded to do some of the nicest maneuvers that I'd ever seen. The good PR had me signed up shortly thereafter, and I have had no second thoughts.
Thanks again guys. Keep the advice flowing.
Clear skies,
Auger
#9
Senior Member
My Feedback: (1)
Plans for transmitter tray
I found the pics in google hevean (try this link). What I did it copyed some text from the page and then searched for that in google with quotes " around it. Then I clicked on "Cached".
I will try to paste them here
I will try to paste them here
Transmitter Tray
By Dick Lahaye
Make flying comfortable and free your hands from having to hold the transmitter case. You can concentrate on fine joystick control movements. This project is real easy and can be finished in a few hours.
Materials required :1/4" plywood, 11" x 14" and 2" x 10".
2 Spruce Runners, 3/4" x 1 1/2" x 9".
2 "L" brackets, 3" x 3" x 3/4" wide.
2 Aluminum Sholder Straps 24" long x 1" wide x 1/8" thick.
4 6x32 machine screws to mount sholder straps to "L" brackets.
4 #6 sheet metal screws to mount "L" brackets to runners.
3/4" brads to mount runners and plywood retainer to Tray top.
Construction: (Refer to diagrams below)
Cut the Tray Top from 1/4" plywood as per drawing, The only variable is the location of the TX handle. Check your TX for correct location after the main opening has been cut away.
Cut the Runners fron 3/4" spruce and cut the Retainer from 1/4" ply.
Cut 2 Sholder Straps from 1/8" x 1" x 24" long. Then bend the upper ends to follow your the contour of your shoulder. Then drill the bottom of the Straps to fit the angle brackets.
Assemble the Runners to the bottom of the Tray with wood glue and brads, Runners should be flush with back of Tray and flush with TX center opening.
Install the TX Retainer plywood strip with glue and brads, be sure to place Retainer so that the Buddy Cord jack will clear for use.
Install the angle brackets to the bottom of the runners with #6 x 3/4" sheet metal screws.
Check TX for good fit in the Tray, then paint with polyeurethane varnish.
When dry, install the sholder straps to the angle brackets with 6 x 32 x 3/8" machine screws, check for comfortable fit to your body, adjust (bend) as necessary. I placed some foam rubber weather striping under the sholder straps for comfort.
You are finished ! Happy Flying
By Dick Lahaye
Make flying comfortable and free your hands from having to hold the transmitter case. You can concentrate on fine joystick control movements. This project is real easy and can be finished in a few hours.
Materials required :1/4" plywood, 11" x 14" and 2" x 10".
2 Spruce Runners, 3/4" x 1 1/2" x 9".
2 "L" brackets, 3" x 3" x 3/4" wide.
2 Aluminum Sholder Straps 24" long x 1" wide x 1/8" thick.
4 6x32 machine screws to mount sholder straps to "L" brackets.
4 #6 sheet metal screws to mount "L" brackets to runners.
3/4" brads to mount runners and plywood retainer to Tray top.
Construction: (Refer to diagrams below)
Cut the Tray Top from 1/4" plywood as per drawing, The only variable is the location of the TX handle. Check your TX for correct location after the main opening has been cut away.
Cut the Runners fron 3/4" spruce and cut the Retainer from 1/4" ply.
Cut 2 Sholder Straps from 1/8" x 1" x 24" long. Then bend the upper ends to follow your the contour of your shoulder. Then drill the bottom of the Straps to fit the angle brackets.
Assemble the Runners to the bottom of the Tray with wood glue and brads, Runners should be flush with back of Tray and flush with TX center opening.
Install the TX Retainer plywood strip with glue and brads, be sure to place Retainer so that the Buddy Cord jack will clear for use.
Install the angle brackets to the bottom of the runners with #6 x 3/4" sheet metal screws.
Check TX for good fit in the Tray, then paint with polyeurethane varnish.
When dry, install the sholder straps to the angle brackets with 6 x 32 x 3/8" machine screws, check for comfortable fit to your body, adjust (bend) as necessary. I placed some foam rubber weather striping under the sholder straps for comfort.
You are finished ! Happy Flying
The following users liked this post:
oskartek (03-02-2024)
The following users liked this post:
oskartek (03-19-2024)
The following users liked this post:
oskartek (03-19-2024)
#14
Senior Member
Join Date: Jun 2010
Location: Sydney, AUSTRALIA
Posts: 4,786
Likes: 0
Received 0 Likes
on
0 Posts
http://www.rcgroups.com/forums/showthread.php?t=1918461
http://www.wattflyer.com/forums/showthread.php?t=1588
http://www.helifreak.com/showthread.php?t=117427
Even a few videos on Youtube that might give you some ideas.
http://www.youtube.com/watch?v=4jL4EHh8pV8
Flew for over a year with a Kraft tray on a Kraft Series 80 radio when pylon racing., very precise with the palms resting on the side and long control sticks.
Have often considered trying another Tray but the TXs are far more ergonomic these days.
#15
Join Date: Jan 2013
Location: , CT
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Any tray you get should have hand rests on each side of transmitter. Without hand rests your less precise. I built my first tray from wood with a shoulder strap. I found the strap to be uncomfortable because the weight of my arms are on the hand rests. Better to have aluminum hoops over your shoulders.